PIC18F4620-I/ML【PDF 227/286 页】IC MCU FLASH 32KX16 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3818

223页 224页 225页 226页 [227页]228页 229页 230页 231页

1996 Microchip Technology Inc.

DS30412C-page 45

PIC17C4X

7.1

Table Writes to Internal Memory

A table write operation to internal memory causes a

long write operation. The long write is necessary for

programming the internal EPROM. Instruction execu-

tion is halted while in a long write cycle. The long write

will be terminated by any enabled interrupt. To ensure

that the EPROM location has been well programmed,

a minimum programming time is required (see speci-

cation #D114 ). Having only one interrupt enabled to

terminate the long write ensures that no unintentional

interrupts will prematurely terminate the long write.

The sequence of events for programming an internal

program memory location should be:

Disable all interrupt sources, except the source

to terminate EPROM program write.

Raise MCLR/VPP pin to the programming volt-

age.

Clear the WDT.

Do the table write. The interrupt will terminate

the long write.

Verify the memory location (table read).

Note:

Programming requirements must be met.

See timing specication in electrical spec-

ications for the desired device. Violating

these specications (including tempera-

ture) may result in EPROM locations that

are not fully programmed and may lose

their state over time.

7.1.1

TERMINATING LONG WRITES

An interrupt source or reset are the only events that

terminate a long write operation. Terminating the long

write from an interrupt source requires that the inter-

rupt enable and ag bits are set. The GLINTD bit only

enables the vectoring to the interrupt address.

If the T0CKI, RA0/INT, or TMR0 interrupt source is

used to terminate the long write; the interrupt ag, of

the highest priority enabled interrupt, will terminate the

long write and automatically be cleared.

If a peripheral interrupt source is used to terminate the

long write, the interrupt enable and ag bits must be

set. The interrupt ag will not be automatically cleared

upon the vectoring to the interrupt vector address.

If the GLINTD bit is cleared prior to the long write,

when the long write is terminated, the program will

branch to the interrupt vector.

If the GLINTD bit is set prior to the long write, when

the long write is terminated, the program will not vector

to the interrupt address.

Note 1: If an interrupt is pending, the TABLWT is

aborted (an NOP is executed). The

highest priority pending interrupt, from

the T0CKI, RA0/INT, or TMR0 sources

that is enabled, has its ag cleared.

Note 2: If the interrupt is not being used for the

program

write

timing,

the

interrupt

should be disabled. This will ensure that

the interrupt is not lost, nor will it termi-

nate the long write prematurely.

TABLE 7-1:

INTERRUPT - TABLE WRITE INTERACTION

Interrupt

Source

GLINTD

Enable

Bit

Flag

Bit

Action

RA0/INT, TMR0,

T0CKI

Terminate long table write (to internal program

memory), branch to interrupt vector (branch clears

ag bit).

None

Terminate table write, do not branch to interrupt

vector (ag is automatically cleared).

Peripheral

Terminate table write, branch to interrupt vector.

None

Terminate table write, do not branch to interrupt

vector (ag is set).

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式